1.To change the already existing printer settings, SWITCH OFF THE PRINTER, AND then HOLD (station 1 + station 2 simultaneously) for 5 seconds and then simultaneously switch ON the printer.
2.Insert the paper and it’s automatically sucked in to the printer.
3.The printer paper shows station 1 to go to next MENU and station 2 to go to SUBMENUS with in MENUS.
4.and it shows local to EXIT.
5.The following is the exact CONFIGURATIONS BASIC AND IBM CONFIG.
EMULATION --CITIC -IBM
CX EMULATION --EPSON
EMUL. TYPE --TEMP.
DRAFT SPEED --NORMAL
LQ TYPE --NLQ1
BUZZER --YES
INTERFACE --AUTO
BAUD RATE --9600
BIT/CHAR --8
PARITY --NONE
STOP BIT --1
DSR --NO
DCD --NO
PAP.EDGE DETECT --NO
SPECIAL FOEMS --NO
CMPL PIN --NO
After this BASIC CONFIG, the IBM CONFIG is changed as below.
IBM Configuration:
EMULATION --IBM PP II
PASSBOOK --YES
BINDING --VERTICAL
ASCII/KANJI ***** --ASCII
CHAR. SET --PC
PC CHAR SET --437 (INT)
PC TABLE --TABLE 2
CHAR DEFINITION --LQ
CPI --17.1
LF+CR --NO
CR+LF --NO
SLASH ZERO --NO
LINE WIDTH --8 IN
FORM LENGTH --11 IN
LIKE IBM-PP BOF --YES
LIKE IBM-PP TOF --YES
SELECT PNS --NO
6.After settings are made on the printer, it will ask SAVE PARAMETERS, press station 1 to YES (CONFIRM)… IF PARAMETERS ARE NOT PROPERLY SET, PRESS station 2 to DON’T CONFIRM.
7.Switch off and switch on the printer again.
8.Printer settings are completed.
Note:All content is copyrighted to http://sm-information.blogspot.com and may not be reproduced on other websites.
If you have any question regarding this websites or any other post related you can Email us.
2.Insert the paper and it’s automatically sucked in to the printer.
3.The printer paper shows station 1 to go to next MENU and station 2 to go to SUBMENUS with in MENUS.
4.and it shows local to EXIT.
5.The following is the exact CONFIGURATIONS BASIC AND IBM CONFIG.
EMULATION --CITIC -IBM
CX EMULATION --EPSON
EMUL. TYPE --TEMP.
DRAFT SPEED --NORMAL
LQ TYPE --NLQ1
BUZZER --YES
INTERFACE --AUTO
BAUD RATE --9600
BIT/CHAR --8
PARITY --NONE
STOP BIT --1
DSR --NO
DCD --NO
PAP.EDGE DETECT --NO
SPECIAL FOEMS --NO
CMPL PIN --NO
After this BASIC CONFIG, the IBM CONFIG is changed as below.
IBM Configuration:
EMULATION --IBM PP II
PASSBOOK --YES
BINDING --VERTICAL
ASCII/KANJI ***** --ASCII
CHAR. SET --PC
PC CHAR SET --437 (INT)
PC TABLE --TABLE 2
CHAR DEFINITION --LQ
CPI --17.1
LF+CR --NO
CR+LF --NO
SLASH ZERO --NO
LINE WIDTH --8 IN
FORM LENGTH --11 IN
LIKE IBM-PP BOF --YES
LIKE IBM-PP TOF --YES
SELECT PNS --NO
6.After settings are made on the printer, it will ask SAVE PARAMETERS, press station 1 to YES (CONFIRM)… IF PARAMETERS ARE NOT PROPERLY SET, PRESS station 2 to DON’T CONFIRM.
7.Switch off and switch on the printer again.
8.Printer settings are completed.
Note:All content is copyrighted to http://sm-information.blogspot.com and may not be reproduced on other websites.
If you have any question regarding this websites or any other post related you can Email us.
Post Category :
How To Guide
,
Printer Guides
0 Comments For " How To Change Settings On The Printer (LIPI PB2) "